Top 9 Motor Driver Arduino UK – Telescope Accessories

As an Amazon Associate I earn from qualifying purchases.

1. Youmile

#ad

Youmile 5Pcs DC Motor Driver Module L298N Mini 1.5A 2-Way PWM Speed Dual Channel H-Bridge Stepper Motor Driver Board for Arduino Small Car

#ad
Youmile #ad - Use of imported original chip, built-in low on-resistance MOS switch. Dual 1. 5a x 2, built-in thermal protection circuit, do not be afraid motor stall burned, the peak current to be 2.5a, automatic recovery after the temperature dropped. Small size, light weight, 0 standby current, is the ideal choice for your car model. Dual h-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor. Minimal heat, low power consumption, no heat sink, small size, is ideal for battery powered.
BrandYoumile #ad
ManufacturerYoumile #ad
Part NumberGR-YM-230
ModelGR-YM-230

2. Youmile

#ad

Youmile 5-Pack Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for arduino

#ad
Youmile #ad - The signal is shown in the figure. The connecting method is shown inbelow figure after enable ENA ENB. Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled.
BrandYoumile #ad
ManufacturerYoumile #ad
Part NumberTS-YM-078
ModelTS-YM-078

3. DollaTek

#ad

DollaTek 5PCS HG7881 800mA Dual DC Motor Driver Controller Board for Arduino

#ad
DollaTek #ad - Each channel has a continuous output current 800 ma. The module can be driven by two dc motors at the same time or one phase 4 line 2 type stepping motor. 0 The input voltage: 2. 5-12 v. Pcb size 29. 2 mm x 23 mm.
BrandDollaTek #ad
ManufacturerDollaTek #ad

4. Youmile

#ad

Youmile 2PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car With Dupont Cable

#ad
Youmile #ad - The connecting method is shown inbelow figure after enable ENA ENB. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. Package content: 2 x l298n motor drive controller board, 1 x 11. 8" male-female dupont cables 12 PIN, 1 x 19. 6" 28awg wire. The signal is shown in the figure. Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously.
BrandYoumile #ad
ManufacturerYoumile #ad
Part NumberDR-YM-254
ModelDR-YM-254

5. ANGEEK

#ad

ANGEEK L293D Motor Driver Shield Stepper Motor Driver for Arduino Duemilanove Mega UNO R3 AVR ATMEL

#ad
ANGEEK #ad - L293d is a monolithic 4-channel high voltage high-current monolithic driver. Basically, this means that with this chip you can use DC motors and power supplies up to 12 volts. The h bridge is typically an electrical circuit that allows a voltage to be applied to an output in each direction, such as motor. These are some pretty large motors and the chip can deliver a maximum current of 600mA per channel, the L293D chip is also what is known as a kind of H bridge. Can drive 4 dc motors or 2 stepper motors or 2 servos.
BrandANGEEK #ad
ManufacturerANGEEK #ad
Part NumberXF0026

6. DollaTek

#ad

DollaTek L298P Motor Driver Module H-bridge Drive Shield Expansion Board High-Power DC Stepper Motor Controller For Arduino

#ad
DollaTek #ad - Stack design can be directly plugged into the Arduino, easier to use. Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A. The l298p shield dc motor driver has PWM speed control mode; dual high-power H-bridge driver. Use eight high-speed Schottky diodes at motor output as protection. Driven part of the input voltage vs: vin input 6. 5 ~ 12v, pwrin 4. 8 ~ 35v input.
BrandDollaTek #ad
ManufacturerDollaTek #ad

7. Dealikee

#ad

Dealikee 6 Pack Mini L298N DC Motor Driver MX1508 Mini Dual Channel 1.5A 1.5A 2 Way PWM Speed Controller Dual H-Bridge Replace Stepper

#ad
Dealikee #ad - Motor drive module is ideal for use in battery-powered smart car, toy cars, robots. Dual h-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor.

Dual 1. 5a * 2, do not be afraid motor stall burned, the peak current to be 2. 5a, built-in thermal protection circuit, automatic recovery after the temperature dropped. Supply voltage 2v -- 10v, can drive two dc motors or a 4-wire 2-phase stepper motors, can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed. Use of imported original chip, no heat sink, small size, minimal heat, built-in low on-resistance MOS switch, low power consumption, is ideal for battery powered.
BrandDealikee #ad
ManufacturerDealikee #ad
Part Number5598321

8. ELEGOO

#ad

ELEGOO 5 sets 28BYJ-48 5V Stepper Motor + ULN2003 Motor Driver Board for Arduino

#ad
ELEGOO #ad - Drive module board sizein: 1. 37*1. 18*06 ; stepper Motor diameter: 1. 06in ; stepper Motor lines: 9. 45in. Stepper motor with a standard interface could be connected with Driver Board easily. 5 line 4 phase can be used for ordinary uln2003 chip driver, connect to the 2 phase, support the development board´╝îWith convenient use, direct docking. Great packing in a box : 5 set uln2003 stepper motor + Driver Board with a little gift and you can download the datasheets in our website: https://www. Elegoo. Com/download/. A, b, c, d four-phase led indicates the status of the stepper motor work.
BrandELEGOO #ad
ManufacturerELEGOO #ad
Height8.99 cm (3.54 Inches)
Length14.99 cm (5.9 Inches)
Weight0.29 kg (0.65 Pounds)
Width3.89 cm (1.53 Inches)
Part NumberUK-EL-SM-003
ModelUK-EL-SM-003

9. DollaTek

#ad

DollaTek 16-Channel 12-bit PWM Servo Motor Driver I2C Module Board PCA9685 For Arduino/Robot/Raspberry Pi

#ad
DollaTek #ad - 3 pin connectors in groups of 4, so you can plug in 16 servos at one time Servo plugs are slightly wider than 01" so you can only stack 4 next to each other on 01" header.

Contain an i2c-controlled pwm driver with a built-in clock. Support using only two pins to control 16 free-running PWM outputs - you can even chain up 62 breakouts to control up to 992 PWM outputs. 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate. It means, unlike the tlc5940 family, you do not need to continuously send it signals tying up your microcontroller; it's completely free running! 5v compliant, which means you can control it from a 3.3v microcontroller and still safely drive up to 6V outputs this is good when you want to control white or blue LEDs with 3. 4+ forward voltages.
BrandDollaTek #ad
ManufacturerDollaTek #ad